Embryo and blastocyst vitrification
On this page you will learn
- How embryo vitrification differs from oocyte vitrification
- Why the blastocoel is a risk and how artificial collapse helps
- When in development to vitrify, and how to judge the moment
- The bench sequence for a blastocyst
Same principle, different cell
An embryo is vitrified with the same two-step idea you learned on page 50. You use equilibration, then a short exposure to the concentrated vitrification solution, a minimum volume and a fast plunge. The differences come from the embryo itself. A cleavage embryo has several smaller cells, each with a better surface-to-volume ratio than one oocyte, so it tolerates the process well. A blastocyst has a fluid-filled cavity, the blastocoel, and that cavity is the main risk.
The blastocoel problem
The blastocoel is mostly water. During equilibration cryoprotectant reaches it slowly, so a large, expanded blastocyst can still hold enough water to form ice when cooled. The answer is artificial collapse (sometimes called artificial shrinkage) just before vitrification. A laser pulse aimed at the trophectoderm, away from the inner cell mass and ideally at a junction between cells, or a fine needle, lets the fluid out. The blastocyst collapses within minutes. You then vitrify the collapsed blastocyst.
Use the laser exactly as for assisted hatching (page 56): calibrated target, shortest effective pulse, aim away from the inner cell mass. Early blastocysts with little cavity usually do not need collapse; fully expanded and hatching blastocysts usually do. Follow the rule in your protocol.
Choosing the moment
Embryos may be vitrified at the cleavage stage (day 2 or 3) or, more commonly now, at the blastocyst stage on day 5, 6 or occasionally 7. The grade at vitrification (page 38 for Gardner grading) is recorded on the device record, because the clinician uses it later when choosing which embryo to warm. Time-lapse data (page 39) can help you vitrify a blastocyst near its peak rather than after it has started to collapse on its own.
Do not leave a ready blastocyst waiting while you finish a long list. If several are ready, plan the order with the senior embryologist and work in small groups so that no embryo spends too long outside the incubator.
At the bench: vitrifying a blastocyst
- Confirm the patient, the embryos to be vitrified, their grades and the device count with your witness. Labels are already on the devices.
- If required, collapse the blastocyst with a laser pulse in a drop of handling medium, then wait for it to shrink.
- Place the embryo in ES and time the step. Watch it shrink and partly re-expand.
- Move it through the VS drops within the set time, rinsing as you go.
- Load it on the carrier in a minimum volume, check it is on the device under the microscope, and plunge straight into liquid nitrogen.
- Close or cap under nitrogen, transfer to the tank and record the storage address, the grade and the times.
Embryos per device
Many laboratories vitrify one blastocyst per device. This lets the couple and the clinician warm exactly one embryo for a single embryo transfer (page 41) without wasting another. Where more than one embryo is placed on a device, the record must say so clearly, and the clinical team must agree in advance.
After vitrification
Check the dish under the microscope before you discard it, to be sure no embryo has been left behind. Update the patient's embryology record, the storage map and the witness log. A blastocyst that was biopsied for testing (page 57) carries an additional link between its device and its biopsy tube, and that link is part of the record.
Common errors
- Vitrifying a fully expanded blastocyst without collapsing it, when the protocol requires collapse.
- Aiming the laser near the inner cell mass.
- Leaving ready blastocysts in room air while finishing a long list.
- Discarding the dish without checking it is empty.
- Placing two embryos on one device without recording it.
Key points
- Embryos are vitrified with the same two-step idea as oocytes: ES, a short VS exposure, a minimum volume and a fast plunge.
- The blastocoel is mostly water and is the main risk; fully expanded blastocysts usually need artificial collapse.
- Aim the laser at the trophectoderm, away from the inner cell mass.
- Record the grade at vitrification; many laboratories vitrify one blastocyst per device.
- Check that the dish is empty before you discard it, and update every record.
Check yourself
Why is a large blastocoel a risk during vitrification?
The blastocoel is mostly water, and cryoprotectant reaches it slowly during equilibration. A large, expanded blastocyst can still hold enough water to form ice when cooled.
Describe how and where you would collapse a blastocyst before vitrifying it.
Just before vitrification, aim a laser pulse at the trophectoderm, away from the inner cell mass. Ideally aim at a junction between cells; a fine needle can also be used. The fluid comes out, and you vitrify the collapsed blastocyst.
Give one reason for vitrifying one blastocyst per device.
The couple and the clinician can then warm exactly one embryo for a single embryo transfer without wasting another.
Why is the embryo grade recorded on the device record?
Because the clinician uses it later when choosing which embryo to warm.
From page 36: Explain how the blastocoel forms.
The outer cells form tight junctions that seal the embryo and pump sodium ions inwards. Water follows by osmosis, and a fluid-filled cavity appears (page 36).
From page 50: Why is time in ES measured in minutes and time in VS in seconds?
Equilibration is slow, as cryoprotectant enters the cell. The concentrated VS becomes toxic if contact is long (page 50).
Questions on this page
Does artificial collapse harm the blastocyst?
When done correctly, the trophectoderm reseals and the blastocyst re-expands after warming. It is a standard step for expanded blastocysts.
Is it better to vitrify on day 3 or day 5?
Both are used. The choice depends on the number and quality of embryos and on the clinical plan. It is decided by the senior embryologist with the clinician.
What if a blastocyst starts collapsing on its own before vitrification?
Spontaneous collapse is common. Note it, and vitrify when the protocol says; the senior embryologist decides whether to wait for re-expansion.
The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Training Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.
