IVF centre in Goa
Consultations in Panjim · Margao · Mapusa · Vasco
Call
Page 31 of 72Embryologist path · Lab Textbook
Part 2: The IVF laboratory, oocytes and ICSI · Day 6
Page 31 of 72

ICSI injection, step by step

On this page you will learn

The principle

The aim is simple to state and takes practice to do well. Place one immobilised sperm deep in the ooplasm, with the oolemma truly broken, away from the meiotic spindle. Use as little fluid and as little distortion as possible, while keeping the oocyte out of the incubator for the shortest time. Every step below serves one of these aims.

Orienting the oocyte

The second meiotic spindle is usually close to the first polar body, though not always directly under it. To keep the injection pipette away from it, the oocyte is held with the polar body at the 12 o'clock or 6 o'clock position. The pipette enters at 3 o'clock. Where polarised light imaging is available (page 28), you can see the spindle and position it directly.

At the bench: the injection

  1. Prepare. The rig is aligned (page 29) and a sperm is immobilised and loaded tail first (page 30). Only now take the MII oocytes from their holding dish and place them in the oocyte drops of the ICSI dish, after checking both dish identities with your witness. Then move the injection pipette into the first oocyte drop.
  2. Hold. Bring the holding pipette to an oocyte. Use the injection pipette to roll the oocyte gently until the polar body is at 12 or 6 o'clock. Apply light suction to hold it. The oocyte should be held firmly without being sucked in or dented.
  3. Focus. Focus on the equator of the oocyte so the oolemma at 3 o'clock is a sharp line. Both pipette tips must be sharp in this same plane.
  4. Position the sperm. Push the sperm forward until it sits just behind the bevel of the injection pipette.
  5. Through the zona. Advance the pipette at 3 o'clock straight through the zona. You will see the zona give and then the tip pass through.
  6. Into the ooplasm. Keep advancing towards the far side of the oocyte, about two thirds of the way across. The oolemma usually stretches inwards ahead of the tip, making a funnel.
  7. Break the oolemma. Apply gentle suction. When the membrane breaks, the ooplasm flows suddenly into the pipette. This sudden flow is your sign of a true break. Stop sucking at once.
  8. Deliver. Gently push the aspirated ooplasm back into the oocyte, followed by the sperm, with a minimum of PVP. Leave the sperm deep in the ooplasm.
  9. Withdraw. Withdraw the pipette slowly and smoothly. Watch the entry point: it should close, and the sperm should stay where you placed it.
  10. Release. Release the suction, let the oocyte go, and move it to a separate area of the drop so injected and uninjected oocytes cannot be confused.

Repeat for each MII oocyte with a fresh immobilised sperm. Inject at a steady pace and do not leave the dish on the stage longer than needed.

1. Hold: polar body 12 or 62. Focus on the equator3. Through the zona at 34. Suction: oolemma breaks5. Deliver; little PVP6. Withdraw and release
Figure: the main steps of one injection.

After the injection

Why each detail matters

Injecting at 3 o'clock keeps the pipette away from the spindle region. Breaking the membrane with suction makes sure the sperm meets the ooplasm, not a pocket of membrane. Using little fluid and little suction protects the ooplasm and its organisation. Releasing promptly and returning oocytes to culture protects temperature and pH. When fertilisation is poor, these are the first points your supervisor will review on your worksheet (page 34).

Common errors

Page 34 groups these and other errors so you can trace their causes.

Key points

Check yourself

  1. Where do you place the polar body, and why?

    At 12 or 6 o'clock, with the pipette entering at 3 o'clock. This keeps the pipette away from the meiotic spindle, which is usually close to the first polar body.

  2. How do you know that the oolemma has truly broken?

    When you apply gentle suction, the ooplasm flows suddenly into the pipette. That sudden flow is the sign of a true break.

  3. Why do you note the time of injection?

    Because the fertilisation check is timed from it (page 33).

  4. List what you record for each oocyte after injection.

    Anything unusual: a very easy or very difficult membrane break, leakage of ooplasm, or degeneration.

  5. From page 26: Why can an MII oocyte look like an MI oocyte?

    A polar body can hide behind the oocyte, so an MII can look like an MI until you rotate it (page 26).

  6. From page 30: What happens if you press the tail too lightly during immobilisation?

    The sperm stops briefly but its membrane stays intact, which risks fertilisation failure (page 30).

Contents and reading plan

Questions on this page

What happens if the oolemma does not break?

If you deliver the sperm without breaking the membrane, it can end up in a pocket of membrane outside the ooplasm and fertilisation may fail. Use gentle suction until you see the sudden flow that shows a true break.

How long should an injection take?

With practice, each injection is short and smooth. The more important rule is that the dish spends as little time out of the incubator as possible; work steadily rather than fast.

Will I inject real oocytes as a trainee?

Training begins on practice material and moves to clinical work only under direct supervision, as your logbook and assessment allow. See page 61.

The Genesis ART Textbook is teaching text for trainees and doctors of the Genesis ART Training Academy. It is not treatment advice and not a laboratory standard operating procedure; every technique is learned under supervision. Page numbers never change.